Lift height and run length trade against each other · review
A four-inlet macerator that publishes its lift, its flow, its inlet sizes and — crucially — the water temperature it will accept.
The bottom line The most connections and a stated hot-water tolerance. What it does not tell you is how far sideways it will push, which is half the question.
A 500 W (0.7 hp) macerator with a stainless cutter, an IPX8 waterproof copper motor, four inlets — one at 89 mm and three at 40 mm — a stated 110 l/min flow, up to 8 m of vertical lift, a 75 °C inlet tolerance and a start delay.
75 °C. A washing machine dumps water close to boiling. A macerator not rated for it fails at the seals, slowly and expensively.
That one figure is what makes this a utility-room unit rather than a bathroom-only one.
One 89 mm — a WC. Three 40 mm — a basin, a shower, an appliance. A whole small bathroom on one box.
Horizontal run. Vertical lift and horizontal distance are traded against each other: a pump that lifts 8 m straight up pushes much further sideways, and the further it goes sideways the less it lifts. Two other macerators in this hub publish both figures; this one publishes only the lift.
It is a toilet that needs electricity. When the power goes off, the WC connected to a macerator is unusable after one flush. That is not a fault — it is the nature of the device — and it belongs in the decision, particularly if it will be the only toilet in a basement flat.
On sale from 103 € to 109 € on the German, French, Italian and Spanish Amazon stores at the time of checking.
Also on sale on the American Amazon store, in the local currency: the range above is measured on the euro stores only.
Listed but with no offer on the British Amazon store — the reference exists there and nobody is currently selling it.
Prices and availability are what Keepa reported on the date this page was updated; both move.
Prices quoted in this text were read on 5 September 2026. The live price is at the top of the page.
| Stated vertical lift | Up to 8 metres — stated |
|---|---|
| Stated horizontal run | Not stated by the maker |
| Inlets | Four — one at 89 mm and three at 40 mm, stated |
| Maximum inlet temperature | 75 °C — stated, for washing machine and dishwasher discharge |
| Discharge diameter | Not stated by the maker |
| Stated noise level | Not stated by the maker |
| Amazon reference | B0F43BJW15 (same reference on 6 Amazon marketplaces) |
| EAN | 0197988131304 |
A washing machine discharges near-boiling water and a dishwasher not far off. A macerator rated only for cold or warm waste will have its seals cooked by that. 75 °C is what lets those appliances be connected at all, and it is the figure that decides the unit's scope.
Nothing drains. A macerator is a WC that depends on electricity, and when the power is off the toilet connected to it cannot be used more than once. No listing in this hub mentions it; it is the thing to know before designing a basement bathroom around one.
Macerator · 400 W · 8 m vertical lift · 100 l/min · three inlets stated in the title, two in the text · carbon filter vent · float switch
A 400 W macerator with a carbon-filtered vent — and a listing that says three inlets in its title and two in its own description.
Best for: A small basement bathroom where smell is the concern, and where the inlet count can be confirmed with the seller first.
≈ £110 / 120 €
Macerator · 700 W with stainless cutter · 9 m lift · 90 m run · 140 l/min · four inlets (3 × 40 mm, 1 × 100 mm) · 80 °C · carbon filter · 17 × 40 × 26 cm
The most completely specified macerator in the catalogue: lift, run, flow, four inlet sizes, an 80 °C limit, a carbon filter and its own external dimensions.
Best for: A complete basement or outbuilding bathroom — WC, basin, shower and an appliance — with a long run back to the stack.
≈ 126 €
Macerator · 600 W · 10 m lift · 200 l/min · three inlets (1 × DN100, 2 × DN40) · 90 °C · automatic operation · descaling stated as the maintenance
The highest lift, the highest flow and the highest temperature tolerance in the catalogue — 10 m, 200 l/min and 90 °C — from the fewest inlets.
Best for: A demanding installation — a high lift, or hot appliance waste — where headroom on every figure matters more than the number of connections.
≈ 135 €
