Lift height and run length trade against each other · review
The most completely specified macerator in the catalogue: lift, run, flow, four inlet sizes, an 80 °C limit, a carbon filter and its own external dimensions.
The bottom line The macerator you can actually design an installation around: every figure published, and the box measured. Only the noise is missing.
A 700 W macerator with a stainless cutter, four inlets — three at 40 mm and one at 100 mm — a stated 140 l/min, up to 9 m of lift, up to 90 m of run, an 80 °C inlet tolerance, automatic start/stop, a non-return valve, overheat protection, a backflow stop, a carbon filter on the vent, a full accessory pack and external dimensions of about 17 × 40 × 26 cm.
Lift. Run. Flow. Four inlet diameters. Temperature limit. External dimensions. Accessories itemised.
Every other macerator in this hub is missing at least two of those, and one of them contradicts itself about how many inlets it has.
A WC. One macerator in this hub cannot take a toilet at all because all its inlets are 40 mm. This one has the WC connection plus three more, with couplings, clips and blanking plugs so the unused inlets are sealed properly rather than taped.
Washing machine, dishwasher, hot bath water — all within tolerance. The units here rated at 65 and 75 °C narrow what can be connected.
A noise figure, on the biggest motor in the hub. One macerator here publishes 30 to 40 dB; this one publishes nothing, and 700 W behind a bathroom panel is not silent.
Every macerator makes drainage depend on the electricity supply. If this serves the only WC in a basement flat, a power cut is a real problem — and no listing on this shelf mentions it.
On sale from 126 € to 135 € on the German and French Amazon stores at the time of checking.
Listed but with no offer on the Italian and Spanish Amazon stores — the reference exists there and nobody is currently selling it.
Not found on the American and British Amazon stores, where the buy link falls back to a local search rather than to a page that does not exist.
Prices and availability are what Keepa reported on the date this page was updated; both move.
Prices quoted in this text were read on 5 September 2026. The live price is at the top of the page.
| Stated vertical lift | Up to 9 metres — stated |
|---|---|
| Stated horizontal run | Up to 90 metres — stated |
| Inlets | Four — three at 40 mm and one at 100 mm, stated, with couplings, clips and blanking plugs supplied |
| Maximum inlet temperature | 80 °C — stated |
| Discharge diameter | Not stated as a figure — an angled outlet piece with a non-return valve is supplied |
| Stated noise level | Not stated by the maker |
| Amazon reference | B0FX9SPT4V (same reference on 4 Amazon marketplaces) |
| EAN | 4260649285848 |
Because the unit has to physically fit behind the pan or inside the vanity. 17 cm deep, 40 cm wide, 26 cm high. It is the only macerator in this hub to publish them, and it is the measurement that stops a delivery going straight back.
It stops what has been pumped up the rise from draining back into the tank when the motor stops. Without one the pump cycles repeatedly on the same water, which wears the motor and makes the noise happen twice as often.
Macerator · 400 W · 8 m vertical lift · 100 l/min · three inlets stated in the title, two in the text · carbon filter vent · float switch
A 400 W macerator with a carbon-filtered vent — and a listing that says three inlets in its title and two in its own description.
Best for: A small basement bathroom where smell is the concern, and where the inlet count can be confirmed with the seller first.
≈ £110 / 120 €
Macerator · 500 W · 8 m vertical lift · 110 l/min · four inlets (1 × 89 mm, 3 × 40 mm) · 75 °C inlet · IPX8 copper motor
A four-inlet macerator that publishes its lift, its flow, its inlet sizes and — crucially — the water temperature it will accept.
Best for: A basement utility room where a WC, a shower, a basin and a washing machine all discharge to one point.
≈ $94 / 103 €
Macerator · 600 W · 10 m lift · 200 l/min · three inlets (1 × DN100, 2 × DN40) · 90 °C · automatic operation · descaling stated as the maintenance
The highest lift, the highest flow and the highest temperature tolerance in the catalogue — 10 m, 200 l/min and 90 °C — from the fewest inlets.
Best for: A demanding installation — a high lift, or hot appliance waste — where headroom on every figure matters more than the number of connections.
≈ 135 €
